Ethylene Gas Sensor Transmitter

μGard®2 (developed by MSR) is the new exchangeable sensor unit that is capable of digital value processing, temperature compensation, and self-control for the continuous monitoring of the ambient air to detect Ethylene(C2H4)Combustible Flammable Gas.

The MC2-X-P3410-X-X is a sensor element at its core with many possible customizations. The beauty of the microgard 2 system is a microcontroller integrated into the  Catalytic Pellistor Ethylene(C2H4) sensor module. The integrated temperature compensation ensures the highest accuracy, selectivity, and reliability despite the long calibration interval. The microcontroller calculates a linear 4-20 mA (or 2-10V) signal out of the measurement signal of the Semi-Conductor sensor and also stores all relevant measured values and data of the sensor element.

Calibration is a breeze with this modular design allowing easy swapping of the sensor unit or via the use of the integrated calibration routine directly at the system.

FEATURES:

  • Fully sealed diffusion catalytic combustible detector and reference element with poison resistant catalytic (with least cross-sensitivity, least carbonization, least fault alarm, and maximum sensor life)
  • Plug and play type concept for field calibration, laboratory calibration and site calibration (where the housing of the gas sensor remains on to the wall with cable wiring and later sensor cell transmitter cartridge can be plug in after calibration)
  • Digital measurement value processing incl. temperature compensation
  • Data / Measured values stored in the microcontroller on the sensor unit allowing easy swap of an old sensor with a newly calibrated sensor.
  • High accuracy, selectivity, and reliability
  • Low zero point drift
  • Sensor lifetime: Refer the datasheet 
  • SIL2 Compliant development process
  • Easy maintenance and calibration by the exchange of the sensor module or by integrated on-site calibration.
  • 4-20 mA (or 2-10V) analog output with selectable signal output for special mode, fault, etc.
  • Reverse polarity protected, overload and short-circuit proof
  • Integrated heating down to -35°C
  • Optional:
    • Without housing
    • With housing Plastic: Type D, 94 x 65 x 57 mm
    • 4-20 mA output signal
    • 2-10 V output signal
    • With display for values and operation, 2x open collector for horn and warning lamp
    • Conformity to:
      o EN 50271
      o EN 50545: 2017
      o EN 61010-1
      o ANSI/UL 61010 1
      o CAN/CSA-C22.2 No. 61010-1
    •  Duct mounting kit (accessory)

Built for standard output of 4-20 mA / 2-10V analog signal output, this transmitter is compatible with the PolyGard 2 series controllers & Sensor Boards as well as any other electronic control or automation system.

Should you have any questions or concerns regarding this matter, please feel free to contact us or reach our experts to info@alviautomation.comsales@gasalarm.com.au

Be sure, Be safe – Gas Detectors and Alarm Systems

Categories: , , Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Description

μGard®2 (developed by MSR) is the new exchangeable sensor unit that is capable of digital value processing, temperature compensation, and self-control for the continuous monitoring of the ambient air to detect Ethylene(C2H4)Combustible Flammable Gas.

The MC2-X-P3410-X-X is a sensor element at its core with many possible customizations. The beauty of the microgard 2 system is a microcontroller integrated into the  Catalytic Pellistor Ethylene(C2H4) sensor module. The integrated temperature compensation ensures the highest accuracy, selectivity, and reliability despite the long calibration interval. The microcontroller calculates a linear 4-20 mA (or 2-10V) signal out of the measurement signal of the Semi-Conductor sensor and also stores all relevant measured values and data of the sensor element.

Calibration is a breeze with this modular design allowing easy swapping of the sensor unit or via the use of the integrated calibration routine directly at the system.

FEATURES:

  • Fully sealed diffusion catalytic combustible detector and reference element with poison resistant catalytic (with least cross-sensitivity, least carbonization, least fault alarm, and maximum sensor life)
  • Plug and play type concept for field calibration, laboratory calibration and site calibration (where the housing of the gas sensor remains on to the wall with cable wiring and later sensor cell transmitter cartridge can be plug in after calibration)
  • Digital measurement value processing incl. temperature compensation
  • Data / Measured values stored in the microcontroller on the sensor unit allowing easy swap of an old sensor with a newly calibrated sensor.
  • High accuracy, selectivity, and reliability
  • Low zero point drift
  • Sensor lifetime: Refer the datasheet 
  • SIL2 Compliant development process
  • Easy maintenance and calibration by the exchange of the sensor module or by integrated on-site calibration.
  • 4-20 mA (or 2-10V) analog output with selectable signal output for special mode, fault, etc.
  • Reverse polarity protected, overload and short-circuit proof
  • Integrated heating down to -35°C
  • Optional:
    • Without housing
    • With housing Plastic: Type D, 94 x 65 x 57 mm
    • 4-20 mA output signal
    • 2-10 V output signal
    • With display for values and operation, 2x open collector for horn and warning lamp
    • Conformity to:
      o EN 50271
      o EN 50545: 2017
      o EN 61010-1
      o ANSI/UL 61010 1
      o CAN/CSA-C22.2 No. 61010-1
    •  Duct mounting kit (accessory)

Built for standard output of 4-20 mA / 2-10V analog signal output, this transmitter is compatible with the PolyGard 2 series controllers & Sensor Boards as well as any other electronic control or automation system.

Should you have any questions or concerns regarding this matter, please feel free to contact us or reach our experts to info@alviautomation.comsales@gasalarm.com.au

Be sure, Be safe – Gas Detectors and Alarm Systems